Windshield Wipers

thanks for the info. I have looked, because mine are getting hard, but have not had any luck either. I will go with your info and see what I can find.

Posts: 88 | Location: Green Valley AZ | Member Since: 10-31-2009

Ignored post by Jerry Jelsing posted

"Host" of Barthmobile.com
Supporting Member of Barthmobile.com

1/19

posted

I like the Trico "64-201" it's a 3 Ridge 20" commercial duty blade made for heavier arm spring loads. I have recommended this blade in the past and it's what I have on my Barth.

NAPA also sells these same Trico wiper blades - Part Number: WIP 602071 it'll come in a NAPA Box, but it is a Trico "64-201"

I think (can't swear to it) the Anco 52-20 has less of a radius bend and it doesn't handle a heavier arm spring load - it might not give you full contact on the corner or tear easier if that's the case. Sadly, I couldn't find the specs on the ANCO website...

When the blade does a sweep, make sure the arm has plenty of room away from the glass, years of use, wrong blade arch and abuse could cause the arm to be "Too Close" to the windshield and this will lead to the windshield getting scraped up.

These blades, whatever the brand, might not make "Full Contact" if there is not enough tension on the arm. Sometimes, slightly bending the arm might give you better blade contact by giving you a better tension load.

Of course, bending an arm to give you better tension isn't meant to take the place of a weak spring arm. It's only meant to give you a better arch by getting the arm in a better position. Too much of a bend can cause the plastic clip to snap if it's not aligning properly and too much tension is placed in the wiper arm swivel.

Wiper sweep is an important consideration. Make sure that at high speed and wet, the wiper arm doesn't scrape up against the rubber windshield molding or go too far off the edge of the windshield.

quote:
TRICO 64 SERIES WIPER BLADES

64 Series blades are designed for heavy duty arms that have 48 oz. of load or more. These three bar blades may be used on both curved and flat windshields. Five part numbers available in lengths from 16 to 20 inches.

Do not use the TRICO 63-200 20"Wiper Blade. The TRICO 63 Series blades are designed for less than 48 oz. of load.

˙ʎ˙u ןןıq- „ǝןƃuɐ ʇuǝɹǝɟɟıp ɐ ɯoɹɟ pןɹoʍ ǝɥʇ ʇɐ ʞooן ɐ ƃuıʞɐʇ sı ǝɟıן oʇ ʇǝɹɔǝs ǝɥʇ„
	1990 Barth Regis Widebody 8908 0128 40RDS-C1 L-10 Cummins Allison MT647 Transmission Spartan Chassis	1991 Medical Lab Conversion 9102 3709 33S-12 Ford 460 MPFI C6 Transmission Oshkosh Chassis
Quick Link: Members Only Link To Send Me A Private Message

Posts: 5924 | Location: Newburgh, New York | Member Since: 05-10-2003

Ignored post by Bill N.Y. posted

Dana

3/22

posted

quote:
I like the Trico "64-201" it's a 3 Ridge 20" commercial duty blade made for heavier arm spring loads. I have recommended this blade in the past and it's what I have on my Barth.

Bill when I got to Yuma I had no rubber on the blades so we went looking. I needed them right now! I never thought it would be so hard to find one to replace. Now that I have it sitting at home and have time I can see the Trico is a heavier pressure blade and will order a pair and keep the others for emergency backups. Thanks for jumping in. I would have hated for someone to put the Anco on and had issues because not enough pressure or durability.

Posts: 1418 | Location: Waseca, Minnesota | Member Since: 12-09-2010

Ignored post by Dana posted

Jerry Jelsing

2/14

posted

Thanks bill for the info. I will go looking for those.

Posts: 88 | Location: Green Valley AZ | Member Since: 10-31-2009

Ignored post by Jerry Jelsing posted

carlflack

1/12

posted

I had serious trouble locating Trico blades 64-201
The best I could do was Amozon, etc. on line with some substantial shipping charges. I sent an E-mail to Trico and received a reply from Dawn Gonzalez stating the 64-201 is "branded under the NAPA name, the part interchange number is 60-2071", if not in stock they can order it.............

Former owner of "THE TOY"
1988 Barth Regal SE 33' Tag
1992 Barth Breakaway 32'
2005 Coachmen Mirada 32' DS

Posts: 592 | Location: North Fort Myers, Florida, USA | Member Since: 11-20-2004

Ignored post by carlflack posted

Dana

3/22

posted

quote:
Trico blades 64-201

Easy find just go to Amazon.com. I had them in less than a week. Replaced and have the others as spares. A whole world of difference. Much heaveier duty blade than the Amco blade.

Posts: 1418 | Location: Waseca, Minnesota | Member Since: 12-09-2010

Ignored post by Dana posted

billyt53

8/11

posted

Talk about a timely post! We have been unhappy with our wiper blades since we bought our Barth 6 years ago. It has 24" wiper blades and have been slapping the end trim and doing a poor job of wiping, particularly in the center of the windshield. I was going to log on this morning to ask if anyone knew what the original blades were! I will look around for the 64-201 Trico's this morning! Happy Barth'ing.

Breaux Bridge GTG 3 days away......

Billy & Helen Thibodeaux

Retired from Billy Thibodeaux's Premiere RV, Inc. Scott, LA 70583 I-10 Exit 97
The Farm is near Duson, LA I-10 Exit 92 then N 1 mile on right
Three Full 50 Amp RV Hookups !
billynhelen@me.com
Data Tag: 9404-3908-36XI-2C
1994 Sovereign 36' Widebody on Spartan IC (Mountain Master Lite) Chassis.
Powered by Cummins ISL9-450
Onan 8,000 Quiet Diesel Genset
Toad: 2018 Chevy Colorado ZR2 Diesel with M&G Car Brake

Posts: 401 | Location: 1mile north of I-10 Exit 92, Duson, LA USA in The Heart of CAJUN COUNRTY ! ! ! | Member Since: 05-14-2005

Ignored post by billyt53 posted

Tom and Julie

3/11

posted

I bought the Trico blades "for curved windshields" and they do not work on the Regency. They will not wipe the flat center of the glass. Am checking with the manuals for a flat windshield blade.

1993 32' Regency Wide Body, 4 speed Allison Trans, Front Entry door, Diamond Plate aluminum roof &
1981 Euro 22' w Chevy 350 engine and TH 400 tranny

Posts: 1514 | Location: Houston Texas | Member Since: 12-19-2006

Ignored post by Tom and Julie posted

"Host" of Barthmobile.com
Supporting Member of Barthmobile.com

1/19

posted

quote:
Originally posted by Tom K:
They will not wipe the flat center of the glass.

Two things to try... Remove the shim that came in the package and/or loosen up the screw that hold them on. I had the same problem when I put my first set on and had to remove that extra shim.

˙ʎ˙u ןןıq- „ǝןƃuɐ ʇuǝɹǝɟɟıp ɐ ɯoɹɟ pןɹoʍ ǝɥʇ ʇɐ ʞooן ɐ ƃuıʞɐʇ sı ǝɟıן oʇ ʇǝɹɔǝs ǝɥʇ„
	1990 Barth Regis Widebody 8908 0128 40RDS-C1 L-10 Cummins Allison MT647 Transmission Spartan Chassis	1991 Medical Lab Conversion 9102 3709 33S-12 Ford 460 MPFI C6 Transmission Oshkosh Chassis
Quick Link: Members Only Link To Send Me A Private Message

Posts: 5924 | Location: Newburgh, New York | Member Since: 05-10-2003

Ignored post by Bill N.Y. posted

bill h

First Month Member

11/13

posted

quote:
Originally posted by Tom K:
I bought the Trico blades "for curved windshields" and they do not work on the Regency. They will not wipe the flat center of the glass.

Tom, what was the Trico number for those blades?

.

84 30T PeeThirty-Something, 502 powered

Posts: 6169 | Location: AZ Central Highlands | Member Since: 01-09-2001

Ignored post by bill h posted

"Host" of Barthmobile.com
Supporting Member of Barthmobile.com

1/19

posted

Another thought...

quote:
These blades, whatever the brand, might not make "Full Contact" if there is not enough tension on the arm. Sometimes, slightly bending the arm might give you better blade contact by giving you a better tension load.

Of course, bending an arm to give you better tension isn't meant to take the place of a weak spring arm. It's only meant to give you a better arch by getting the arm in a better position.

˙ʎ˙u ןןıq- „ǝןƃuɐ ʇuǝɹǝɟɟıp ɐ ɯoɹɟ pןɹoʍ ǝɥʇ ʇɐ ʞooן ɐ ƃuıʞɐʇ sı ǝɟıן oʇ ʇǝɹɔǝs ǝɥʇ„
	1990 Barth Regis Widebody 8908 0128 40RDS-C1 L-10 Cummins Allison MT647 Transmission Spartan Chassis	1991 Medical Lab Conversion 9102 3709 33S-12 Ford 460 MPFI C6 Transmission Oshkosh Chassis
Quick Link: Members Only Link To Send Me A Private Message

Posts: 5924 | Location: Newburgh, New York | Member Since: 05-10-2003

Ignored post by Bill N.Y. posted

Tom and Julie

3/11

posted

Trico 64-201 which were purchased after reading the posts. I had the end slapping problem which was traced to the cracked knurled spacer on the mount, but the windshield is basically flat through the center of the windshield to the curve near the outside. I had hoped to have it wipe the flat area and curve around the side to increase the view but it just rode at the top and bottom leaving the entire center wet. I am ready to forget the curved part and just make the flat area clear.

1993 32' Regency Wide Body, 4 speed Allison Trans, Front Entry door, Diamond Plate aluminum roof &
1981 Euro 22' w Chevy 350 engine and TH 400 tranny

Posts: 1514 | Location: Houston Texas | Member Since: 12-19-2006

Ignored post by Tom and Julie posted

"Host" of Barthmobile.com
Supporting Member of Barthmobile.com

1/19

posted

quote:
Originally posted by Tom K:
I bought the Trico blades "for curved windshields" and they do not work on the Regency.

The Regency windshields are the same as all of the other windshields. Barth only had the Early era 68 to mid 73 windshields and then everything else was the same with the exception of the center section widebody 6" insert or the standard body 4" insert from the waning years.

So, I'm going to go with my earlier quote as I really don't see what else it could be.

quote:
These blades, whatever the brand, might not make "Full Contact" if there is not enough tension on the arm. Sometimes, slightly bending the arm might give you better blade contact by giving you a better tension load.

Of course, bending an arm to give you better tension isn't meant to take the place of a weak spring arm. It's only meant to give you a better arch by getting the arm in a better position.

quote:
Two things to try... Remove the shim that came in the package and/or loosen up the screw that hold them on. I had the same problem when I put my first set on and had to remove that extra shim.

˙ʎ˙u ןןıq- „ǝןƃuɐ ʇuǝɹǝɟɟıp ɐ ɯoɹɟ pןɹoʍ ǝɥʇ ʇɐ ʞooן ɐ ƃuıʞɐʇ sı ǝɟıן oʇ ʇǝɹɔǝs ǝɥʇ„
	1990 Barth Regis Widebody 8908 0128 40RDS-C1 L-10 Cummins Allison MT647 Transmission Spartan Chassis	1991 Medical Lab Conversion 9102 3709 33S-12 Ford 460 MPFI C6 Transmission Oshkosh Chassis
Quick Link: Members Only Link To Send Me A Private Message

Posts: 5924 | Location: Newburgh, New York | Member Since: 05-10-2003

Ignored post by Bill N.Y. posted

bill h

First Month Member

11/13

posted

quote:
Originally posted by Mogan David:
The differences:
http://test.tricoproducts.com/..._wiper_sellsheet.pdf

It is interesting to note that the second page of that site shows a 64 series for a 20 inch blade, but shows 67 series for longer blades.

Anybody know what the difference between series is?

I am considering either longer blades because I sit above the wiped area of the windshield. I am tall with a long torso, so I sit high. I have to scrunch down in the rain too see out. Not a big issue, because I work really hard not to drive in the rain. My crappy eyesight loses depth perception in rain.

Another way to go would be to make up some kind of extender to allow my blades to mount farther out on the arms. Longer or higher blades would make the ends hit the center divider or edges, I think, but a micarta or nylon ramp mounted at the right place would lift the arm at that extreme end of its travel, minimizing blade rubber damage.

.

84 30T PeeThirty-Something, 502 powered

Posts: 6169 | Location: AZ Central Highlands | Member Since: 01-09-2001

Ignored post by bill h posted